Evaluation of surface roughness and color changes of restorative materials used with different polishing procedures in pediatric dentistry

Basit Öğe Kaydı
dc.authoridPEKER, OYKU/0000-0002-3698-6225
dc.contributor.authorPeker, Oyku
dc.contributor.authorBolgul, Behiye
dc.date.accessioned2024-09-18T20:54:08Z
dc.date.available2024-09-18T20:54:08Z
dc.date.issued2023
dc.departmentHatay Mustafa Kemal Üniversitesien_US
dc.description.abstractThis study aimed to evaluate the color stability and surface roughness properties of four different restorative materials used in pediatric dentistry clinics as a result of four different polishing procedures. A total of 128 samples, 32 of each restorative material, were prepared by placing them in polyethylene molds with a diameter of 6 mm and a height of 2 mm, in accordance with the instructions of the manufacturers, to be polished with four different polishing procedures (n = 8). After finishing and polishing, the samples were kept in distilled water at 37 degrees C for 24 hours. Surface roughness and color stability measurements of the samples were then made. The Hysitron TI 950 TriboIndenter device in Mustafa Kemal University's Technology Research & Development Center was used for surface roughness test measurements, and the Ra parameter was taken as a basis. A spectrophotometer instrument (VITA Easyshade & REG; Advance 4.0 (VITA Zahnfabrik, Bad Sackingen, Germany)) was used to determine color stability and color differences were recorded according to the CIEDE 2000 system. The lowest roughness values were observed in G-aenial restorative material polished with Super-Snap material, and the highest roughness values were observed in Equia material polished with Identoflex material. When all materials were evaluated, the smallest color change values were seen in G-aenial material polished with SuperSnap, and the most color change values were detected in Equia material polished with Identoflex. It was observed that the relationship between surface roughness and color change was statistically significant. The lowest color change and surface roughness values were observed in the G-aenial material polished with Super-Snap. For improved clinical results, the most appropriate polishing procedure should be chosen based on the restorative material used.en_US
dc.identifier.doi10.22514/jocpd.2023.037
dc.identifier.endpage79en_US
dc.identifier.issn1053-4628
dc.identifier.issn1557-5268
dc.identifier.issue4en_US
dc.identifier.pmid37408349en_US
dc.identifier.scopus2-s2.0-85163932131en_US
dc.identifier.scopusqualityQ3en_US
dc.identifier.startpage72en_US
dc.identifier.urihttps://doi.org/10.22514/jocpd.2023.037
dc.identifier.urihttps://hdl.handle.net/20.500.12483/11608
dc.identifier.volume47en_US
dc.identifier.wosWOS:001034362800010en_US
dc.identifier.wosqualityQ2en_US
dc.indekslendigikaynakWeb of Scienceen_US
dc.indekslendigikaynakScopusen_US
dc.indekslendigikaynakPubMeden_US
dc.language.isoenen_US
dc.publisherMre Pressen_US
dc.relation.ispartofJournal of Clinical Pediatric Dentistryen_US
dc.relation.publicationcategoryMakale - Uluslararası Hakemli Dergi - Kurum Öğretim Elemanıen_US
dc.rightsinfo:eu-repo/semantics/openAccessen_US
dc.subjectPediatric dentistryen_US
dc.subjectPolishing proceduresen_US
dc.subjectColor changeen_US
dc.subjectSurface roughnessen_US
dc.titleEvaluation of surface roughness and color changes of restorative materials used with different polishing procedures in pediatric dentistryen_US
dc.typeArticleen_US

Dosyalar

Orijinal paket
Listeleniyor 1 - 1 / 1
Küçük Resim
İsim:
Tam Metin / Full Text
Boyut:
309.14 KB
Biçim:
Adobe Portable Document Format
İndir

Koleksiyon

WoS İndeksli Yayınlar Koleksiyonu
PubMed İndeksli Yayınlar Koleksiyonu
Scopus İndeksli Yayınlar Koleksiyonu